CB Series Carbon Block Filters

• Reduce taste/odor/chlorine and certain VOC’s from drinking water*
• Great chlorine removal capacity competitive with the finest carbon blocks*
• Nominal 0.5, 1, 5, and 10 micron Available

LIQUATEC CB SERIES CARBON BLOCK FILTERS

Are manufactured with high purity Coconut Shell activated carbon. Available in a wide range of lengths, diameters, and micron ratings our Liquatec blocks provide an exceptional cost-to-performance value. With high chlorine reduction, great dirt-holding capacity, and greatly reduced carbon fines, you will soon make the CB series your carbon block of choice.

LIQUATEC CB SERIES CARBON BLOCK FILTERS
Are ideal for point-of-use (POU) and Reverse Osmosis applications. These cartridges can be used in a wide range of applications such as residential, food service, commercial, and industrial. The CB Series carbon blocks are great for displacing traditional GAC (Granular Activated Carbon) and PAC (Powdered Activated Carbon) filters in application where high chlorine reduction is needed. Because of your overall lower cost, our CB Series are able to compete with virtually all carbon blocks manufactured in the USA.

ITEM #                                                                  O.D.
X LENGTH		 WEIGHT* CHLORINE
CAPACITY*		 MICRON
RATING
NOMINAL*		 INITIAL DP (psi)
@ FLOW RATE (gpm)*
MCB10 2.5”x9 7/8” 1.3lb 20,000 @ 1gpm  0.5μm 4.0 psid @ 0.5gpm
CB-250-975-01  2.5”x9 7/8” 1.2lb 6,000 @ 0.75gpm 1μm 4.0 psid @ 0.75gpm
CB-250-975-05 2.5”x9 7/8” .99lb 6,000 @ 1gpm 5μm 2.0 psid @ 1.0gpm
CB-250-975-10 2.5”x9 7/8” .81lb 6,000 @ 1.5gpm 10μm 2.0 psid @ 1.0gpm
CB-250-20-01 2.5”x20” 2.10lb 12,000 @ 1.5gpm 1μm 4.0 psid @ 1.5gpm
CB-250-20-05 2.5”x20” 1.80lb 9,000 @ 2gpm 5μm 2.0 psid @ 2.0gpm
CB-250-20-10 2.5”x20” 1.60lb 9,000 @ 2.5gpm 10μm 2.0 psid @ 2.0gpm

 
   

ITEM # O.D.
X LENGTH		 WEIGHT* CHLORINE
CAPACITY*		 MICRON
RATING
NOMINAL*		 INITIAL DP (psi)
@ FLOW RATE (gpm)*
CB-450-975-01 4.5”x9 7/8” 3.2 lb 20,000 @ 2.5gpm 1μm 7.0 psid @ 2.5gpm
CB-450-975-05 4.5”x9 7/8” 2.7 lb 12,000 @ 3.5gpm 5μm 4.0psid @ 3.5gpm
CB-450-975-10 4.5”x9 7/8” 2.0 lb 12,000 @ 4gpm 10μm 4.0 psid @ 4gpm
CB-450-20-01 4.5”x 20” 6.4 lb 17,000 @ 1gpm 1μm 6.5 psid @ 5.0gpm
CB-450-20-05 4.5”x 20” 5.4 lb 26,000 @ 7gpm 5μm 4.5 psid @ 7.0gpm
CB-450-20-10 4.5”x 20” 4.2 lb 26,000 @ 8gpm 10μm 4.5 psid @ 8.0gpm

* Weights, chlorine capacity, micron rating, pressure drop, percent efficiency and initial DP (PSI) @ flow rate tested by manufacturer and independent laboratory.

Not Performance Tested or Certified by NSF.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.

NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. CB series cartridges will contain a very small amount of carbon fines (very fine black powder). After installation follow the instructions for flushing the cartridge to remove all traces of the fines before using the water. You should run (flush) the tap at least 20 seconds prior to using water for drinking or cooking purposes. This is particularly important if the tap has not been used daily.

NOTE: Micron ratings based on 85% or greater removal of given particle size.
  
   
  
  

  • Carbon
 Coconut Shell
  • End Cap
 Polypropylene
  • Outer Wrap
 Polypropylene
  • Inner Wrap
 Polypropylene
  • Netting
 Polypropylene
  • Gasket
 Neoprene
  • Temperature Rating
 40°F to 180°F

* Tested and certified by NSF International to ANSI/NSF Standard 42 for material requirements only.